View KS57P21408_27253.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

KS57C21408/C21418/P21408
PRODUCT OVERVIEW
1
OVERVIEW
PRODUCT OVERVIEW
The KS57C21408/C21418/P21408 is a SAM47 core-based 4-bit CMOS single-chip microcontroller. It has a timer/counter and LCD drivers. The KS57P21408 is especially suited for use in data bank, telephone and LCD general purpose. It is built around the SAM47 core CPU and contains ROM, RAM, 39 I/O lines, programmable timer/counter, buzzer output, enough LCD dot matrix, and segment drive pins. The KS57C21408/C21418/P21408 can be used for dedicated control functions in a variety of applications, and is especially designed for multi data bank, telephone and LCD game.
OTP
The KS57C21408/C21418 microcontroller is also available in OTP (One Time Programmable) version, KS57P21408. KS57P21408 microcontroller has an on-chip 8 K-byte one-time-programable EPROM instead of masked ROM. The KS57P21408 is comparable to KS57C21408/C21418, both in function and in pin configuration.
1-1
PRODUCT OVERVIEW
KS57C21408/C21418/P21408
FEATURES SUMMARY
Memory * * * * 8192 x 8 bit program memory 5120 x 4 bit data memory in KS57C21408 2560 x 4 bit data memory in KS57C21418 108 x 5 bit display memory LCD Display * * * 12 characters dot matrix display (5 x 7) 12 digit display (8 segments) 60 segments and 9 common pins
Power-Down Modes * * Idle mode (only CPU clock stops) Stop mode (Main-System clock and CPU clock stops)
39 I/O Pins * * * Input: 6 pins I/O: 17 pins Output: maximum 16 pins for 1-bit level output (sharing with segment driver outputs)
Oscillation Sources * * * * Crystal, ceramic, or External RC for system clock Main-system clock frequency: 0.4 MHz - 6MHz Sub-system clock frequency: 32,768kHz CPU clock divider circuit (by 4,8, or 64)
8-Bit Basic Timer * Four internal timer functions
8-Bit Timer/Counter 0 * * * * Programmable 8-bit timer External event counter Arbitrary clock frequency output External clock signal divider Instruction Execution Times * * * 0.67, 1.33, 10.7 s at 6MHz 0.95, 1.91, 15.3 s at 4.19 MHz 122 s at 32.768 kHz
Watch Timer * * Time interval generation: 0,5ms, 3,9ms at 32768Hz 4 frequency (2/4/8/16 kHz) outputs to BUZ pin
Operating Temperature * -45 C to 85 C
Operating Voltage Range * 1.8 V to 5.5 V
Interrupts * * * Three external vectored interrupts: INT0, INT1, INTP0 Two internal vectored interrupts: INTB, INTT0 Two quasi-interrupts: INTW, INT2 Package Type * 100-pin QFP Package
Memory Mapped I/O Structure
1-2
KS57C21408/C21418/P21408
PRODUCT OVERVIEW
BLOCK DIAGRAM
INTT0, INTB, INTW INT0, INT1, INTP0, INT2
RESET
XIN XOUT XTIN XTOUT Input Port 0
P0.0-P0.3/ K0-K3
8-Bit Timer/ Counter 0
Interrupt Control Block
Clock
Instruction Register
Input Port 1
P1.0/INT0 P1.1/INT1
Watch Timer
Internal Interrupts
Program Counter
I/O Port 2
P2.0/BUZ P2.1/CLO P4.0/TCL0 P4.1/TCLO0 P4.2 P5.0-P5.3
I/O Port 4 Basic Timer Instruction Decoder Program Status Word I/O Port 5
COM0-COM8 SEG16-SEG59 SEG0-SEG15 /P8.0-P8.15
LCD Driver/ Controller
Arithmetic and Logic Unit
Stack Pointer
I/O Port 6 I/O Port 7
P6.0-P6.3/ KS0-KS3 P7.0-P7.3/ KS4-KS7
Data and Display Memory
8 K Byte Program Memory
Output Port 8
P8.0-P8.15/ SEG0-SEG15
NOTE: Data memory:
5120 x 4 bits in KS57C21408 2560 x 4 bits in KS57C21418 Display memory: 108 x 5 bits
Figure 1-1. KS57C21408/C21418/P21408 Specified Block Diagram
1-3
PRODUCT OVERVIEW
KS57C21408/C21418/P21408
PIN ASSIGNMENTS
SEG39 SEG40 SEG41 SEG42 SEG43 SEG44 SEG45 SEG46 SEG47 SEG48 SEG49 SEG50 SEG51 SEG52 SEG53 SEG54 SEG55 SEG56 SEG57 SEG58 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
SEG59 COM4 COM5 COM6 COM7 COM8 P6.0/KS0 P6.1/KS1 P6.2/KS2 P6.3/KS3 P7.0/KS4 P7.1/KS5 P7.2/KS6 P7.3/KS7 VDD VSS Xout Xin TEST XTin XTout
RESET
P2.0/BUZ P2.1/CLO P5.0 P5.1 P5.2 P5.3 TCL0/P4.0 TCLO0/P4.1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
KS57C21408/C21418
100-QFP 1420C
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
SEG38 SEG37 SEG36 SEG35 SEG34 SEG33 SEG32 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15/P8.15 SEG14/P8.14 SEG13/P8.13 SEG12/P8.12 SEG11/P8.11 SEG10/P8.10 SEG9/P8.9
Figure 1-2. KS57C21408/C21418 Pin Assignment Diagram
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 SEG8/P8.8 SEG7/P8.7 SEG6/P8.6 SEG5/P8.5 SEG4/P8.4 SEG3/P8.3 SEG2/P8.2 SEG1/P8.1 SEG0/P8.0 COM3 COM2 COM1 COM0 INT0/P1.0 INT1/P1.1 P0.0/K0 P0.1/K1 P0.2/K2 P0.3/K3 P4.2
1-4
KS57C21408/C21418/P21408
PRODUCT OVERVIEW
PIN DESCRIPTIONS
Table 1-1. Pin Descriptions Pin Description Type I P0.0 - P0.3 4-bit input port. 1 and 4-bit read, and test are possible. Pull-up registers. 2-bit Input port. P1.0 I 1 and 4-bit read, and test are possible, 2-bit pull-up P1.1 resistors are assignable by software. P2.0 I/O 2-bit I/O port. 1 and 4-bit read/write, and test are possible. P2.1 Each individual pin can be specified as input or output. 2-bit pull-up resistors are assignable by software. Pull-up resistors are automatically disabled for output pins. P4.0 I/O 4-bit I/O port. 1, 4, and 8-bit read/write, and test are possible. P4.1 4-pin unit can be specified as input or output. P4.2 4-bit pull-up resistors are assignable by software. P5.0 - P5.3 Pull-up resistors are automatically disabled for output pins. Individual pins are software configurable as opendrain or push-pull output. P6.0 - P6.3 I/O 4-bit I/O port. 1, 4,and 8-bit read/write, and test are possible. Each individual pin can be specified as input or output. 4-bit pull-up resistors are assignable by software. Pull-up resistors are automatically disabled for output pins. P7.0 - P7.3 4-bit I/O port. 1, 4, and 8-bit read/write, and test are possible. 4-pin unit can be specified as input or output. 4-bit pull-up resistors are assignable by software. Pull-up resistors are automatically disabled for output pins. P8.0 - P8.15 O 4-bit controllable output. (Dual function as segment output pins) SEG16-SEG59 LCD segment display signal output. SEG0 - SEG15 COM0 - COM8 INT0 - INT1 KS0 - KS7 K0 - K3 I I/O I LCD segment display signal output. LCD common signal output. External interrupts. The triggering edge for INT0, and INT1 is selectable Quasi-interrupt input for falling edge detection. Vector interrupt input K0 - K3: falling edge detection Pin Name Circuit Pin Type Number A-1 35-32 Share Pin K0-K3
A-3
37 36 23 24
INT0 INT1 BUZ CLO
D
E E-1 E-1 E-1
29 30 31 25-28
TCL0 TCLO0
D-1
7-10
KS0 - KS3
11-14
KS4 - KS7
H-9 H-10 H-9 H-11
42-57 58-100 ,1 42-57 38-41 2-6 37-36 7-14 35-32
SEG0 SEG15 P8.0 - P8.15 P1.0 -P1.1 P6.0 - P7.3 P0.0 - P0.3
1-5
PRODUCT OVERVIEW
KS57C21408/C21418/P21408
Table 1-1. Pin Descriptions (Continued) Pin Name BUZ CLO Xin, Xout XTin, XTout TCL0 TCLO0
RESET
Pin Description Type I/O 2,4,8 kHz or 16kHz frequency output for buzzer signal. Clock output I/O I/O I I Crystal, ceramic or RC oscillator pins for main system clock. Crystal oscillator pins for sub-system clock. External clock input for Timer/Counter 0 Timer/Counter 0 clock output Reset input (active low). Power supply. Ground. Test input: it must be connected to VSS
Circuit Type B -
Pin Num. 23 24 18, 17 20, 21 29 30 22 15 16 19
Share Pin P2.0 P2.1 P4.0 P4.1 -
VDD VSS TEST
1-6
KS57C21408/C21418/P21408
PRODUCT OVERVIEW
PIN CIRCUIT DIAGRAMS
VDD Pull-up Resistor P-channel IN N-channel IN
Pull-up Resistor Enable
VDD
P-channel
Schmitt Trigger
Vss
Figure 1-3. Pin Circuit Type A
Figure 1-5. Pin Circuit Type A-3
VDD
VDD
Pull-up
Pull-up Register
Pull-up Resistor Enable IN
P-channel
IN
Schmitt Trigger
Figure 1-4. Pin Circuit Type A-1
Figure 1-6. Pin Circuit Type B
1-7
PRODUCT OVERVIEW
KS57C21408/C21418/P21408
VDD
VDD
Pull-up Resistor
Pull-up Resistor Enable
Data
P-channel
P-channel
OUT N-channel Output Disable VSS
Data Output Disable Type C
IN/OUT
Schmitt Trigger
Figure 1-7. Pin Circuit Type C
Figure 1-9. Pin Circuit Type D-1
VDD Pull-Up Resistor
Pull-Up Resistor Enable Data Output Disable Type C
PNE VDD
VDD Pull-up Resistor
P-channel
Data
P-channel I/O
Pull-up Resistor Enable
In/Out
Output Disable
N-channel
Schmitt Trigger
Figure 1-8. Pin Circuit Type D
Figure 1-10. Pin Circuit Type E
1-8
KS57C21408/C21418/P21408
PRODUCT OVERVIEW
VDD PNE VDD Pull-up resistor
Data
P-channel I/O
Pull-up Resistor Enable
VLC2 Segment Data
OUT
Output Disable
N-channel
VLC0
Figure 1-11. Pin Circuit Type E-1
Figure 1-13. Pin Circuit Type H-10
VDD
SEG Data/P8.0-P8.15
VLC1 VLC2
VLC0
OUT
OUT COM Data
Vss
Key strobe
Vss
Polarity
Vss
Figure 1-12. Pin Circuit Type H-9
Figure 1-14. Pin Circuit Type H-11
1-9
PRODUCT OVERVIEW
KS57C21408/C21418/P21408
NOTES
1-10
KS57C21408/C21418/P21408
ELECTRICAL DATA
13
OVERVIEW
ELECTRICAL DATA
In this section, information on KS57C21408/C21418/P21408 electrical characteristics is presented as tables and graphics. The information is arranged in the following order: STANDARD ELECTRICAL CHARACTERISTICS -- Absolute maximum ratings -- D.C electrical characteristics -- Main-system clock oscillator characteristics -- Sub-system clock oscillator characteristics -- I/O capacitance -- A.C electrical characteristics -- Operating voltage range MISCELLANEOUS TIMING WAVEFORMS -- A.C timing measurement point -- Clock timing measurement at Xin -- Clock timing measurement at XTin -- TCL0 timing -- Input timing for RESET -- Input timing for external interrupts STOP MODE CHARACTERISTICS AND TIMING WAVEFORMS -- RAM data retention supply voltage in stop mode -- Stop mode release timing when initiated by RESET -- Stop mode release timing when initiated by an interrupt request
13-1
ELECTRICAL DATA
KS57C21408/C21418/P21408
Table 13-1. Absolute Maximum Ratings (TA = 25 C) Parameter Supply Voltage Input Voltage Output Voltage High Level Output current Low Level Output Current All pins Operating Temperature Storage Temperature
NOTE : RMS value = Peak Value x Duty .
Symbol VDD VI VO IOH IOL One pin
Conditions - Ports 0, 1, 2, 4, 5, 6, 7 -
Rating - 0.3 to + 6.5 - 0.3 to VDD + 0.3 - 0.3 to VDD + 0.3 - 15 - 30 30 15 100 60 - 40 to + 85 - 65 to + 150
Units V V V mA mA mA mA mA mA
C C
All output pins One pin Peak value RMS value (note) Peak value RMS value (note) TA TSTG - -
Table 13-2. D.C Characteristics (TA = - 40 C to + 85 C, VDD = 1.8 V to 5.5 V) Parameter Input High Voltage Symbol VIH1 VIH2 VIH3 Input Low Voltage VIL1 VIL2 VIL3 Output High Voltage VOH1 Conditions Pins except below Port0, 1, 6, 7, P4.0, RESET XIN, XOUT and XTIN All input pins except below Port0, 1, 6, 7, P4.0, RESET XIN,XOUT and XTIN VDD = 4.5 V to 5.5 V Port2, 4, 5, 6, 7 IOH = - 1mA VDD - 1.0 Min. 0.7 VDD 0.8 VDD VDD - 0.1 - Typ. - - - - - - - Max. VDD VDD VDD 0.3 VDD 0.2 VDD 0.1 - Units V
13-2
KS57C21408/C21418/P21408
ELECTRICAL DATA
Table 13-2. D.C Characteristics(continued) (TA = - 40 C to + 85C, VDD = 1.8 V to 5.5 V) Parameter Output Low Voltage Symbol VOL1 Conditions VDD = 4.5 V to 5.5 V Port2, 4, 5, 6, 7 IOL= 15mA VDD = 1.8 V to 5.5 V IOL=1.6mA Input High Leakage Current ILIH1 ILIH2 Input Low Leakage Current ILIL1 Vin = VDD All input pins except below Vin = VDD XIN, XOUT, XTIN VIN = 0 V All input pins except XIN, XOUT, XTIN and RESET VIN = 0 V XIN, XOUT, XTIN VO = VDD Port2, 4, 5, 6, 7 VO = 0 V Port2, 4, 5, 6, 7 VDD = 5 V, VIN = 0 V All pins except RESET VDD = 3 V VDD = 5 V, VIN = 0 V
RESET
Min. -
Typ. -
Max. 2
Units
- -
- -
0.4 3 20 A
-
-
-3
ILIL2 Output High Leakage Current Output Low Leakage Current Pull-up Resistor ILOH1 ILOL1 RL1
- - - 25 50 100 200 VM1 - 0.2 VM2 - 0.2 VM3 - 0.2 VM4 - 0.2 SEG0-SEG59 COM0-COM8 - - - - -
- - - 50 100 250 500 VM1 VM2 VM3 VM4 - - - - -
- 20 3 -3 100 200 400 800 VM1 + 0.2 VM2 + 0.2 VM3 + 0.2 VM4 + 0.2 90 25 90 2 25 k K V K
RL2
VDD = 3 V Medium Output Voltage(1) VOM1 VOM2 VOM3 VOM4 High Output Impedance Low Output Resistor ROH1 ROH2 ROL1 ROL2 ROL3 VO = 0.5V COM0-COM8 COM0-COM8 SEG0-CSEG59 SEG0-CSEG59 VO = VDD-0.5V
SEG0-SEG59 SEG0-SEG15 (key strobe) COM0-COM8
13-3
ELECTRICAL DATA
KS57C21408/C21418/P21408
Table 13-2. D.C Characteristics (continued) (TA = - 40 C to + 85C, VDD = 1.8 V to 5.5 V) Parameter Supply Current
(2) (3)
Symbol IDD1
Conditions Run mode : VDD = 5 V 10% Crystal oscillator C1 = C2 = 22pF VDD = 3 V 10% 6MHz 4.19MHz 6MHz 4.19MHz
Min. -
Typ. 5.1 3.8 2.5 1.8 1.3 1.1 0.5 0.4
Max. 8 6 4 3 2.5 1.8 1.5 1.0 45 30
Units mA
IDD2
Idle mode : VDD = 5 V 10% Crystal oscillator C1 = C2 = 22pF VDD = 3 V 10%
6MHz 4.19MHz 6MHz 4.19MHz
IDD3 IDD4
Run mode: VDD = 3 V 10% 32kHz crystal oscillator Idle mode: VDD = 3 V 10% 32kHz crystal oscillator VDD = 3 V 10% 32kHz crystal oscillator LCD ON (4)
- -
30 17
A
LCD OFF -
6 2.4 0.6
15 5 3
IDD5
Stop mode; VDD = 5 V 10%, XTIN = 0V Stop mode; VDD = 3 V 10%, XTIN = 0V
NOTES: 1. VM1=2.75/3.75 VDD, VM2=1/3.75 VDD, VM3=2/3.75 VDD, VM4=1.75/3.75 VDD 2. 3. 4. Supply current does not include current drawn through internal pull-down resistor and LCD driving resistors. For D.C. electrical voltages, PCON register must be set to 0011B. The mode of IDD4 (LCD ON) is normal.
13-4
KS57C21408/C21418/P21408
ELECTRICAL DATA
Table 13-3. Main System Clock Oscillator Characteristics (TA = - 40 C + 85 C, VDD = 1.8 V to 5.5 V) Oscillator Ceramic Oscillator Clock Configuration
XIN XOUT
Parameter Oscillation frequency(fx) (1)
Test Condition -
Min 0.4
Typ -
Max 6.0
Units MHz
C1
C2
Stabilization time (2)
After VDD reaches the minimum level of its variable range -
-
-
4
ms
Crystal Oscillator
XIN
XOUT
Oscillation frequency(fx) (1)
0.4
-
6
MHz
C1
C2
Stabilization time (2) External Clock
XIN XOUT
VDD = 4.5 V to 5.5 V VDD = 1.8 V to 5.5 V -
- - 0.4
- - -
10 60 6
ms MHz
Xin input frequency(fx) (1)
Xin input high and low level width (tXH, tXL) RC Oscillator
XIN R XOUT
- VDD = 5 V
83.3 -
- 2
1250 -
ns MHz
Frequency
VDD = 3 V
-
1
-
NOTES: 1. Oscillation frequency and input frequency data are for oscillator characteristics only. 2. Stabilization time is the interval required for oscillator stabilization after a power-on or release of STOP mode.
13-5
ELECTRICAL DATA
KS57C21408/C21418/P21408
Table 13-4. Recommended Oscillator Constants (TA = - 40 C + 85 C, VDD = 1.8 V to 5.5 V) Manufacturer Series Number (1) FCR FCR CCR M5 MC5 MC3 Frequency Range Load Cap (pF) C1 TDK 3.58 MHz-6.0 MHz 3.58 MHz-6.0 MHz 3.58 MHz-6.0 MHz 33
(2)
Oscillator Voltage Range (V) MIN 2.0 2.0 2.0 MAX 5.5 5.5 5.5
Remarks
C2 33
(2)
Leaded Type On-chip C Leaded Type On-chip C SMD Type
(3)
(3)
NOTES: 1. Please specify normal oscillator frequency. 2. On-chip C: 30pF built in. 3. On-chip C: 38pF built in.
13-6
KS57C21408/C21418/P21408
ELECTRICAL DATA
Table 13-5. Subsystem Clock Oscillator Characteristics (TA = - 40 C + 85 C, VDD = 1.8 V to 5.5 V) Oscillator Crystal Oscillator Clock Configuration
XTIN XTOUT
Parameter Oscillation frequency (1)
Test Condition -
Min 32
Typ 32.768
Max 35
Units kHz
C1
C2
Stabilization time (2)
VDD = 4.5 V to 5.5 V VDD = 1.8 V to 5.5 V
- - 32
1.0 - -
2 10 100
ms
External Clock
XTIN XTOUT
XTin input frequency (1)
-
kHz
XTin input high and low level width (tXTH, tXTL)
-
5
-
15
s
NOTES: 1. Oscillation frequency and input frequency data are for oscillator characteristics only. 2. Stabilization time is the interval required for oscillating stabilization after a power-on or release of STOP mode.
Table 13-6. Input/Output Capacitance (TA = 25 C, VDD = 0 V ) Parameter Input Capacitance Output Capacitance I/O Capacitance Symbol CIN COUT CIO Condition f = 1 MHz; Unmeasured pins are returned to VSS Min - - - Typ - - - Max 15 15 15 Units pF pF pF
13-7
ELECTRICAL DATA
KS57C21408/C21418/P21408
Table 13-7. A.C. Electrical Characteristics (TA = - 40 C to + 85 C, VDD = 1.8 V to 5.5 V) Parameter Instruction Cycle Time (NOTE) Symbol tCY Conditions VDD = 2.7 V to 5.5 V VDD = 1.8 V to 5.5 V With sub-system clock (fxt) TCL0 Input Frequency TCL0 Input High, Low Width f TI VDD = 2.7 V to 5.5 V VDD = 1.8 V to 5.5 V tTIH tTIL tINTH, tINTL VDD = 2.7 V to 5.5 V VDD = 1.8 V to 5.5 V External Interrupt Input High, Low Width
RESET Low Level
Min 0.67 1.33 114 0
Typ -
Max 64
Units s
122 -
1952 1.5 1 MHz kHz s
0.48 1.8
10
-
-
INT0, INT1, KS0 - KS7
-
-
s
KS0 - KS3 tRSL - Width
10 10 - - s
NOTE: Unless otherwise specified, the values of instruction cycle time condition assume a main-system clock (fx) source.
13-8
KS57C21408/C21418/P21408
ELECTRICAL DATA
CPU Clock 1.5 MHz
Main Oscillator Frequency 6 MHz
0.75 MHz
3 MHz
15.625 kHz
400 kHz
1
1.8 V
2
3
4
5
6
7
Supply Voltage(V)
CPU CLOCK = 1/n x oscillator frequency (n = 4, 8, 64)
Figure 13-1. Standard Operating Voltage Range
Table 13-8. RAM Data Retention Supply Voltage in Stop Mode (TA = - 40 C to + 85 C) Parameter Data retention supply voltage Data retention supply current Release signal set time Oscillator stabilization wait time (1) Symbol VDDDR IDDDR tSREL tWAIT Conditions - VDDDR = 1.8 V - Released by RESET Released by interrupt Min 1.8 - 0 - - 2 Typ - 0.1 -
17
Max 5.5 10 - - -
Unit V A s ms
/ fx
(2)
NOTES: 1. During oscillator stabilization time, all CPU operations are stopped to avoid unstable operation upon oscillation start. 2. The basic timer mode register (BMOD) interval timer delays execution of CPU instructions during the wait time.
13-9
ELECTRICAL DATA
KS57C21408/C21418/P21408
TIMING WAVEFORMS
INTERNAL RESET OPERATION STOP MODE DATA RETENTION MODE IDLE MODE OPERATING MODE
VDD
EXECUTION OF STOP INSTRUCTION
RESET
VDDDR
tWAIT tSREL
Figure 13-2. Stop Mode Release Timing When Initiated By RESET
IDLE MODE STOP MODE DATA RETENTION MODE NORMAL OPERATING MODE
VDD
EXECUTION OF STOP INSTRUCTION
VDDDR
tSREL
POWER-DOWN MODE TERMINATING SIGNAL (INTERRUPT REQUEST)
tWAIT
Figure 13-3. Stop Mode Release Timing When Initiated By Interrupt Request
13-10
KS57C21408/C21418/P21408
ELECTRICAL DATA
0.8 VDD 0.2 VDD MEASUREMENT POINTS
0.8 VDD 0.2 VDD
Figure 13-4. A.C. Timing Measurement Points (Except for Xin and XTin)
1 / fx (1 / fXT)
tXL (tXTL)
tXH (tXTH)
Xin (XTin)
VDD - 0.5 V
0.4 V
Figure 13-5. Clock Timing Measurement at Xin and XTin
13-11
ELECTRICAL DATA
KS57C21408/C21418/P21408
1 / fTI
tTIL
TCL0
tTIH
0.8 VDD 0.2 VDD
Figure 13-6. TCL0 Timing
tRSL
RESET
0.2 VDD
Figure 13-7. Input Timing for RESET Signal
tINTL
tINTH
INT0, 1 INTP0 KS0 to KS7
0.8 VDD 0.2 VDD
Figure 13-8. Input Timing for External Interrupts and Quasi-Interrupts
13-12
KS57C21408/C21418/P21408
MECHANICAL DATA
14
OVERVIEW
-- -- -- Pad diagram
MECHANICAL DATA
This section contains the following information about the device package: Package dimensions in millimeters Pad/pin coordinate data table
23.90 0.3 0-8 20.00 0.2 0.15
+0.10 -0.05
17.90 0.3
14.00 0.2
100-QFP-1420C
0.80 0.20
0.10 MAX
#100 (0.83) 0.3 0.1 0.10 MAX 0.65 (0.58)
#1
0.05 MIN 2.65 0.10 3.00 MAX
0.80 0.20 NOTE: Dimensions are in millimeters.
Figure 14-1. 100-QFP-1420 Package Dimensions
14-1
MECHANICAL DATA
KS57C21408/C21418/P21408
NOTES
14-2
KS57C21408/C21418/P21408
KS57P21408 OTP
15
OVERVIEW
KS57P21408 OTP
The KS57P21408 single-chip CMOS microcontroller is the OTP (One Time Programmable) version of the KS57C21408/C21418 microcontroller. It has an on-chip OTP ROM instead of masked ROM. The EPROM is accessed by serial data format. The KS57P21408 is fully compatible with the KS57C21408/C21418, both in function and in pin configuration. Because of its simple programming requirements, the KS57P21408 is ideal for use as an evaluation chip for the KS57C21408/C21418.
15-1
KS57P21408 OTP
KS57C21408/C21418/P21408
SEG39 SEG40 SEG41 SEG42 SEG43 SEG44 SEG45 SEG46 SEG47 SEG48 SEG49 SEG50 SEG51 SEG52 SEG53 SEG54 SEG55 SEG56 SEG57 SEG58 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
SEG59 COM4 COM5 COM6 COM7 COM8 P6.0/KS0 P6.1/KS1 P6.2/KS2 P6.3/KS3 P7.0/KS4 P7.1/KS5 /P7.2/KS6 SDAT /P7.3/KS7 SCLK VDD /VDD VSS/VSS Xout Xin VPP/TEST XTin XTout
RESET / RESET
KS57P21408
100-QFP 1420C
P2.0/BUZ P2.1/CLO P5.0 P5.1 P5.2 P5.3 TCL0/P4.0 TCLO0/P4.1
SEG38 SEG37 SEG36 SEG35 SEG34 SEG33 SEG32 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15/P8.15 SEG14/P8.14 SEG13/P8.13 SEG12/P8.12 SEG11/P8.11 SEG10/P8.10 SEG9/P8.9
Figure 15-1. KS57P21408 Pin Assignments (100-QFP Package)
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 SEG8/P8.8 SEG7/P8.7 SEG6/P8.6 SEG5/P8.5 SEG4/P8.4 SEG3/P8.3 SEG2/P8.2 SEG1/P8.1 SEG0/P8.0 COM3 COM2 COM1 COM0 INT0/P1.0 INT1/P1.1 P0.0/K0 P0.1/K1 P0.2/K2 P0.3/K3 P4.2
15-2
KS57C21408/C21418/P21408
KS57P21408 OTP
Table 15-1. Descriptions of Pins Used to Read/Write the EPROM Main Chip Pin Name P3.1 Pin Name SDAT Pin No. 13 During Programming I/O I/O Function Serial data pin. Output port when reading and input port when writing. Can be assigned as a Input / push-pull output port. Serial clock pin. Input only pin. Power supply pin for EPROM cell writing (indicates that OTP enters into the writing mode). When 12.5 V is applied, OTP is in writing mode and when 5 V is applied, OTP is in reading mode. (Option) Chip initialization Logic power supply pin. VDD should be tied to +5 V during programming.
P3.0 TEST
SCLK VPP(TEST)
14 19
I/O I
RESET
RESET
22 15/16
I I
VDD / VSS
VDD / VSS
Table 15-2. Comparison of KS57P21408 and KS57C21408/C21418 Features Characteristic Program Memory Operating Voltage (VDD) OTP Programming Mode Pin Configuration EPROM Programmability 1.8 V to 5.5 V VDD = 5 V, VPP(TEST)=12.5V 100 QFP User Program 1 time 100 QFP Programmed at the factory KS57P21408 8 Kbyte EPROM KS57C21408 8 Kbyte mask ROM 1.8 V to 5.5V
OPERATING MODE CHARACTERISTICS When 12.5 V is supplied to the VPP(TEST) pin of the KS57P21408, the EPROM programming mode is entered. The operating mode (read, write, or read protection) is selected according to the input signals to the pins listed in Table 15-3 below. Table 15-3. Operating Mode Selection Criteria VDD 5V
VPP
(TEST) 5V 12.5 V 12.5 V 12.5 V
REG/ MEM 0 0 0 1
ADDRESS
R/W 1 0 1 0 EPROM read
MODE
(A15-A0) 0000H 0000H 0000H 0E3FH EPROM program EPROM verify EPROM read protection
NOTE: "0" means Low level; "1" means High level.
15-3
KS57P21408 OTP
KS57C21408/C21418/P21408
Table 15-4. D.C Characteristics (TA = -40 C to +85C, VDD = 1.8 V to 5.5V) Parameter Supply Current
(2)(3)
Symbol IDD1
Conditions Run mode : VDD=5V10% Crystal oscillator C1=C2=22pF VDD=3V10% 6MHz 4.19MHz 6MHz 4.19MHz
Min. -
Typ. 5.1 3.8 2.5 1.8 1.3 1.1 0.5 0.4
Max. 8 6 4 3 2.5 1.8 1.5 1.0 45 30
Units mA
IDD2
Idle mode : VDD=5V10% Crystal oscillator C1=C2=22pF VDD=3V10%
6MHz 4.19MHz 6MHz 4.19MHz
IDD3 IDD4
Run mode : VDD=3V10% 32kHz crystal oscillator Idle mode : VDD=3V10% 32kHz crystal oscillator VDD=3V10% 32kHz crystal oscillator LCD ON(4)
- -
30 17
A
LCD OFF -
6 2.4 0.6
15 5 3
IDD5
Stop mode; VDD=5V10% Stop mode; VDD=3V10%
NOTES: 1. VM1=2.75/3.75 VDD, VM2=1/3.75 VDD, VM3=2/3.75 VDD, VM4=1.75/3.75 VDD 2. Supply current does not include current drawn through internal pull-down resistor and LCD driving resistors. 3. For D.C. electrical voltages, PCON register must be set to 0011B. 5. The mode of IDD4 (LCD ON) is normal.
15-4
KS57C21408/C21418/P21408
KS57P21408 OTP
CPU Clock 1.5 MHz
Main Oscillator Frequency 6 MHz
0.75 MHz
3 MHz
15.625 kHz
400 kHz
1
1.8 V
2
3
4
5
6
7
Supply Voltage(V)
CPU CLOCK = 1/n x oscillator frequency (n = 4, 8, 64)
Figure 15-2. Standard Operating Voltage Range
15-5
KS57P21408 OTP
KS57C21408/C21418/P21408
NOTES
15-6

▲Up To Search▲

Price & Availability of KS57P21408

	To Download KS57P21408 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .